There was a problem loading the comments.

Grandstream HT801

Knowledge Base  »  Viewing Article

  Print
Some articles in the knowledge base for the control panel may refer to the legacy interface which we are updating over time. Please see in your portal for the latest inline documentation.
To setup your adapter, you will first need to create an extension and have your username, password, SIP proxy and STUN server addresses to hand.

The first step will be to login to your adapter via your browser. To obtain the IP address of the adapter, the following steps should be followed:

Plug-in adapter to network
Connect phone handset to device
Dial * * * and wait until you hear "Enter the menu option"
Enter 02

The device will then read back the IP which you should then enter into your browser connected to the same network and you will see a screen with a login prompt.

49c37efebf2c5871a92812d524c48db4f67f1150eea3a01cd679059dd07af628decf22efc532b54b?t=a9055050b48152782a6d18552d0263ff

The default login details for the device should be both admin for the username and password.

Once logged in, you'll be presented with a "Status"

d8fdf638617fbdfe32ac89f5a156a29aaabd17179c26cd4dde6e4e5096b7414c56b098711fcaf441?t=6634d1f9c25fba068c14182d709f014f

Click "FXS PORT" on the top menu and, you'll need to enter values from your extension information as mapped below.

Username > SIP User ID (i.e p1234-myusername)
Username > Authenticate ID (i.e p1234-myusername)
Password > Authenticate Password (your extension password)
SIP Proxy > Primary SIP Server (i.e sip-xxx.voipsrv.net)

Name (The descriptive name for the extension, such as "Home" or "Office")

8d7a2c7b460473ca2f808b967893e6b7e5e10c217757aaa31d1a004d0b8495d10ccdb6f95e97b5f5?t=72ae05a7c458876a864f051aae1625b9

To then allow calls to be made on later firmware versions, the following settings should all be set to Default or No as shown.

Use Privacy Header:                       Default
Use P-Preferred-Identity Header:       Default
Use P-Access-Network-Info Header:       No
Use P-Emergency-Info Header:               No
Use P-Asserted-Identity Header:       No

f001f58d9bf2105df0e63de315bf514df2cf46a338400948d404a808645059a5eba5b0a696811472?t=acb6da094ef018f38d91dbf65032bf79

Additionally, we recommend changing the dial plan (set within "Dial Plan:") to one more suited to UK usage from the default.

{ 155 | 116xxx | 116111 | 116123 | 118xxx | 1471 | 157[1-2] | 08001111 | 0845464x | 0[1235789]xxxxxxxxx | 00xxx. | x+ | \+x+ | *x+ | *xx*x+ }

These changes should then be saved by clicking Apply.

Moving down the page, there are a few settings recommended for UK use related to caller ID formatting.

257f21a48e2c69c2e274b4d0b904dfafa11aa4bee4c5129299a055f16b15a1e9f994e9a7fc23bfc2?t=2208bb91249e97d40dc527821936ebec

SLIC Setting: UK
Caller ID Scheme: SIN 227 - BT

If you are on a NAT network, which is most common for home and office networks, you may need to adjust the settings which work best for you.

NAT Traversal: Keep-Alive or STUN

If set to STUN, please set "STUN server is" on the ADVANCED SETTINGS page.

STUN server is: stun.portfiftysixty.net

To avoid getting anonymous calls that are direct to the ATA, you should disable unauthenticated calls. Some routers will pass through SIP data to devices behind a firewall without question allowing anyone to initiate an IP call with your device.

Allow Incoming SIP Messages from SIP Proxy Only: Yes

Once done, save this page also by clicking Apply.

The adapter may then reboot and incoming and outgoing calls should work as expected.


Comments

Add Comment

Replying to  

© VoIPify